Bitumen Testing Equipment

Standard TAR Viscometer

Standard TAR Viscometer
Item code: EBTE-41

Electrical Heating with Immersion Heating Elements and Dimmer stat for controlling the temperature. Suitable for operation on 230 V, 50Hz, Single Phase , A.C. supply Complete with 10mm cup and valve.

Additional Information:
  • Item Code: EBTE-41

Manual Compaction

Manual Compaction
Item code: EBTE-42

Compaction Mould Comprising Mould body, base plate and combined filling / extraction collar. Satisfies BS 598

Additional Information:
  • Item Code: EBTE-42

Compaction Pedestal

Compaction Pedestal
Item code: EBTE-43

Comprising a 300mm sq x 25mm thick steel plate complete with 4 tie rods and securing nuts. A mould clamp and hammer guide are fitted to the plate. The unit is supplied complete with a laminated hardwood block.

Additional Information:
  • Item Code: EBTE-43

Mixer with Heating Jacket

Mixer with Heating Jacket
Item code: EBTE-44

A 6-litre Mixer Used in conjunction with an Iso Mantle, is suitable for mixing samples of asphalt. Bench mounting Mixer, 6 liter nominal capacity. Supplied with bowl, beater and whisk. Motorised with two speed operated on 230 V A.C., Single Phase.

MANTLE ELECTRIC HEATER

For use of Bench Mounting mixer. For 230 V A.C. , 50Hz, Single Phase.

Additional Information:
  • Item Code: EBTE-44

Marshall Stability Test Apparatus

Marshall Stability Test Apparatus
Item code: EBTE-45

MARSHALL APPARATUS CONSISTS OF:
  • Robust Construction
  • 50KN capacity
  • Rate of travel 50.8mm/min
  • Safety cut-off switch

It consists of body housing, a geared screw jack and motor drive mechanism suitable for operation on 230 V, 50Hz, Single Phase, A.C. supply.

Additional Information:
  • Item Code: EBTE-45

Digital Marshall Stability Test Apparatus

Digital Marshall Stability Test Apparatus
Item code: EBTE-46

This versatile digital loading frame features a microprocessor controlled drive system with stepper motor enabling the operator to easily set any test speed by digital switches. The machine is fitted with an RS 232 C port so it can be remotely controlled by a personal computer. The upper and lower limits of platen travel are set by use of automatic safety cutout switches. All load rings, dial gauges, cells, etc. have to be ordered separately.

Specification :

  • Load capacity : 50kN (5000 kgf)
  • Platen Speeds : Selectable Speed range 0.01 mm to 62mm/min
  • Accuracy of platen speed : 1%
  • Max. vertical daylight : 0-850 mm
  • Platen dia : 180mm
  • Distance between columns : 380mm
  • RS 232 Port for connection to personal computer. L.V.D.T. can be supplied instead of dial gauge fitted with Breaking Head Assembly.

Additional Information:
  • Item Code: EBTE-46

Pavement Core Drilling Machine

Pavement Core Drilling Machine
Item code: EBTE-47

The Pavement Core Drilling Machine. Diesel engine powered road building drill has been designed specifically for the purpose of drilling test cores from or holes in, Roads, Airport Runways, Bridges etc. The Machine comprises of two vertical support columns, which carry the Drill head/Engine assembly with the help of screwed spindle. The 5 HP diesel engine with pulley mechanism works with minimum vibrations. The double precision bit advances with screwed spindle, which provides a constant, accurate drill pressure, minimum core chipping & long bit life. The complete assembly is supplied on a rigid metal base with leveling facility and is suitable for vertically down coring applications only.
  • Bit Diameter : Varying from 25mm to 150mm
  • Maximum depth of core : 700mm
  • Drill Speed : 475 & 800 R.P.M.
  • Guide Shafts : 50mm dia
  • Screwed Spindle : 20mm dia
  • Water Tap : 12mm
  • Drill Wrenches : Included
  • Water Tank : Optional

Additional Information:
  • Item Code: EBTE-47

Automatic Compactor

Automatic Compactor
Item code: EBTE-48
  • Automatic Compactor for Bituminous Mixes
  • Rugged construction to withstand hard work
  • Fully automatic and easy to operate
  • Uniform compaction
  • Automatic Preset Blow Counter

Specification :
The Automatic Compactor eliminates the laborious process of manual compaction and an even degree of compaction is achieved. The driven mechanism lifts the weight of 4.5kg and drops it through a correct height of 457 mm. The rammer foot is removable, which facilitates preheating. A compaction pedestal with specimen holder is fixed to the base. An Automatic Blow counter enables the number of blows to be present before each test and automatically stops the machine on completion. Suitable for operation on 230 V, 50 Hz, Single Phase, A.C. supply

Additional Information:
  • Item Code: EBTE-48

Ductility Testing Apparatus

Ductility Testing Apparatus
Item code: EBTE-49

Designed to test three specimens simultaneously. The machine consists of a carriage moving over a lead screw. An electric motor driven reduction gear unit ensures smooth constant speed and continuous operation. The entire assembly is mounted with a stainless steel lined water bath completely encased in metal bound hardwood. It is equipped with an electric pump circulator and heater. The temperature is controlled thermostatically. Two rates of travel i.e. 5 cm/min and 1 cm/min are provided. Suitable for operation on 230 V, 50 Hz, Single Phase, A.C. supply

Additional Information:
  • Item Code: EBTE-49

Benkelman Beam

BENKELMAN Beam
Item code: EBTE-50
  • Lightweight Aluminium construction
  • Ease of Transportation
  • Unique Telescopic Design Simplifying Field set up
  • Compact, Thereby reducing the amount of storage space needed
Benkelman Beam utilizes the technique of using balanced beam in conjunction with a suitable vehicle to measure road flexure The improved Benkelman Beam is a convenient, accurate device for measuring the deflection of flexible pavements under moving wheel loads. Operating on a simple lever arm principle, the unit consists. Supplied with carrying case.

NOTE :
Benkelman Beam with Digital Dial Gauge also available at an extra cos

Additional Information:
  • Item Code: EBTE-50

Loss on Heating

Loss on Heating/ Thin Film Oven
Item code: EBTE-51 

This dual purpose oven is designed to determine the loss in weight of bitumen and flux oils (Loss on Heating test) and the effect of heat and air on asphaltic materials (Thin Film test). The unit is heavily insulated and has a double glass door for viewing the test chamber thermometer and samples. Temperature is controlled at 163° C ± 1° C by means of a variable temperature controller and thermostat. Two rotating platforms are supplied with each oven: One accepts 9 standard penetration cups for the loss on heating test, the other accepts two 140mm diameter test pans for the thin film test. The platforms are rotated at 5 to 6 rpm by an external motor. Chamber dimensions 350 x 350 x 350mm (length x width x height)

Additional Information:
  • Item Code: EBTE-51

Rolling Thin Film Oven

Rolling Thin Film Oven
Item code: EBTE-52
  • Certified temperature control
  • Digital Display
  • Internal Fan
The Rolling Thin Film Oven Test is used to obtain homogeneously aged material by the application of heat and air in order to simulate these affects in conventional mixing. The oven is of double wall construction with side vents and of the heated convection type of air Circulation. An electronic controller maintains the temperature at 163+ 0.5° C. A vertical, carriage is supplied to support 8 glass sample containers, which are rotated at 15+ 0.2rpm. An outlet orifice 1mm in diameter is connected to a 7.6m length of copper tubing and flow meter which controls the airflow at 4000 ml/min. Air is blown into the sample containers at their lowest point of travel by an internal airjet. The oven is supplied with 8 glass sample containers and a thermometer (IP 47C/ASTM 13C). Internal dimensions 483 x 450 x 381mm. A separate source of compressed air is required to operate this oven.
Operating Voltage 230 V A.C., Single Phase
ACCESSORIES:Compressor Spares Glass sample container Thermometer.

Additional Information:
  • Item Code: EBTE-52

Automatic Road Unevenness Recorder

Automatic Road Unevenness Recorder
Item code: EBTE-53

comprises of a trailer of single wheel with a pneumatic type mounted on chaise over which are installed profile recording and integrating devices. The machine has panel board fitted with two nos. of electronic counters for counting the unevenness index value. The digital meter for unevenness index value from 50 mtrs. To 1000 mtrs. For automatic displaying of UI values Data Storage in memory to display on panel board. The operating SPEED OF THE MACHINE IS 30 + 1-1/2 KM/Hr, and is towed by a vehicle. Its wheel on the pavement surface and the vertical reciprocating motion of the axle is converted into unidirectional rotatory motion by the integrator unit, the accumulation of this unidirectional motion is recorded by operating sensor inserted in the circuit of electronic counter once for every one centimeter of accumulated unevenness. Wheel revolutions are also indicated on the other electronic counter through a sensor actuated by the cam fitted on the hub of the wheel after every one meter of the wheel movement. There is an arrangement introduced for digital display of unevenness index value with a setting of distance form 50 mtrs, to 999 mtrs. In this arrangement suppose we get the distance value of 50 mtrs. Then after every 50 mtrs. We will get calculated U.I. Values on the digital meter In such manner we can set distance in 200 mtr, and so on upto 9999 mtrs. There is a memory of keeping UI values upto last 999 memories. The machine can be supplied with a pair of transportation wheels which will permit towing speed upto 60km/Hr, without disturbing the accuracy of the unevenness measuring wheel.A motor is fitted on the machine which is driven through the sensor and electronic controller form the wheel of the unit and the vertical motion of the axle drives a pen which marks on the moving recording paper. The pavement profile is recorded on the recording paper in the ration of 1:400 for and 1:1 unevenness of the road surface.

USES:

The degree of surface finish or the, riding quality of the road/runway pavement can be assessed. The system will record surface irregularities of highways and runways, which can be immediately attended to for rectification. The records so obtained can be well studied for judgment and decision in classifying pavement surfaces by the authorities for serviceability of the pavement and stage for repair or upgrading. Helps in evaluating the performance of the Specifications adopted for roads and runways and the developments of unevenness with age and under traffic.
ADVANTAGES
  • Timely improving the riding quality will result in
  • Low maintenance cost of pavement and vehicles
  • Increase in the load carrying capacity of the vehicle
  • Prolongs the working life of the vehicles and the driver
  • Comfortable ride to road users
  • Less fatigue to d driver in the interest of road safety
  • Minimize stresses in both road structures and vehicles
SALIENT FEATURES
  • Helps in assessing and improving the riding quality of pavement
  • Gives unevenness index value of pavements
  • Data obtained with various units is inter comparable
  • Safe and stable in operations
  • Durable and dependable
  • Cent percent indigenous
  • A compact and versatile unit at economic price
  • Automatic Road Unevenness Recorder is a single wheel trailer and towed by vehicle like jeep at a speed of 30km/hr uses a micro-controller, which contains a microprocessor and is designed for industrial is used
  • 12 volts 11 plate Battery is used
  • The distance section segment size is adjustable as per the requirement form 50 meters to 9999 meters

Additional Information:
  • Item Code: EBTE-53

Flow Table

FLOW TABLE ED-57208

The flow table test or flow test is a method to determine consistency of fresh concrete. Flow table test is also used to identify transportable moisture limit .

Specification of Flow Table

Use: Flow of hydraulic mortars and cementSpecifications• Table: Cast-bronze; 254 mm (10") diam.; combined weight with shaft, 4.1±0.05 kg. (9 lbs. ±0.1 lb).• Frame: Heavy-duty construction with cam; produces 12.7 mm (1/2") tabledrop.• Flow Mold: Machined bronze; 69.8 mm (2-3/4")top inner diameter x 101.6mm (4") height• Base inner diameter: 50.8 mm (2").

Porker Vibrator

PORKER VIBRATOR ED-57133

Use: compaction of concrete
Specifications PORKER VIBRATOR
• Tip dimensions mm: dia. 25x250mm long• Flexible shaft: 2000mm• Electric operated• Current specifications: 220-230V, 50-60Hz, 1 ph• Power: 500W

Situ Water Permeability Test Kit

IN-SITU WATER PERMEABILITY TEST KIT ED-57135
Use: testing Concrete water permeability
• Pressure chamber unit with 0-1.5 bar gauge & built-in micrometergauge & valves.• Wrench for pressure lid.• Extra 0-6.0 bar gauge.• Water filling cup.• Adjustable clamping pliers.• Set of anchoring tools with drift & hammer.• Wrenches: 14 and 17 mm.• Sealant tape.• Bottles with boiled water, 3 bottles.• Gaskets, 10 mm thick, 4 pcs.• Gaskets, 15 mm thick, 4 pcs.

Concrete Cover Meter

CONCRETE COVER METER ED-57134
Use: Reinforcement depth measurementBar size can be preset if known, or detected automatically for survey andinvestigation tasks. For non-standard bar sizes, large diameter pipes orother pre-fabricated items, it can also show absolute measurements thatcan be used to look up cover using custom tables. For immediate resultson-site, the onscreen gauge and audio feedback rapidly pin-point rebarlocation and orientation. Meets or exceeds the requirements of BS1881part 204 over the full range of the instrumentCover range 5mm – 185 mm
Accuracy:
± 1mm up to 60mm cover± 2mm up to 120mm± 3mm up to 160mm± 4mm over 160mmAutomatic Bar SizingAccuracy ± 0.5mm – ± 1.5 mmResolution 0.1mmOperating Depth6mm bar up to 60mm cover40mm bar up to 80mm coverBar ResolutionBar size:16mm Cover: 60mm Minimum spacing: 70mmBar size: 16mm Cover: 100mm Minimum spacing: 110mmBar size: 25mm Cover: 130mm Minimum spacing: 150mmOperating Weight 800gBattery Operation 20 hrsIngress Protection IP65

Cover meter Includes:

• Probe with integral cable• Battery charger• Spare probe sole-plate• Certificate of Conformity• Light & tough equipment bag

Curve Generator Machine

Curve Generator Machine 

Edutek Instrumentation are offering a wide rrange of  Curve Generator Machine Exporter,  Curve Generator Machine Manufacturer & Supplier of Curve Generator Machine based in Ambala Cantt.
We take pride in introducing ourselves as one of the renowned manufacturers and suppliers of Curve Generator Machines. These are fabricated using premium grade raw materials, which are procured from the authentic vendors of the industry. Designed in conformity with the defined quality standards, these are renowned for their high operational efficiency, trouble free service life and low maintenance cost. Moreover, our customers can purchase these offered machines from us at market leading prices.
Looking for Bitumen Testing Equipment ?
© Edutek Instrumentation
 
Desktop Site Back to top